Can I fit my own outside socket?
How to connect a male plug
- How to connect a male plug
- Where to place sockets in a room?
- What is the name of where the plug is connected?
- Which cable to use for outdoor electrical installation?
- How the wires run in a wall socket
- How high do the outlets go?
- How far apart should there be between outlets?
- Where to place a socket for a hood?
- Decorative outdoor electrical installation
- What is the EU plug?
- What is the positive and negative in a plug?
- What color wire is used for the ground line in an electrical installation?
- How do the wires go in a three-prong plug?
Now, when someone thinks about buying an electric car, many doubts arise, among which almost always stand out those that refer to the autonomy of the battery and, logically, to the recharge. One of the most recurrent concerns the installation of a charging point, especially when the car sleeps in a communal garage. What should I do to install a charger? Can the owners’ association object? Where do I get the electricity from? Below, we will try to find answers to all these questions in order to clarify the issues surrounding the purchase of a vehicle with these characteristics.
In the same way that you can install it in the garage of a single-family house, you can also do it in a community parking lot, although you will have to communicate it previously to the president of the community or to the administrator. You have to announce it with 30 days of anticipation to the beginning of the work and to contribute the corresponding technical certification once the installation has finished.
Where to place sockets in a room?
It is recommended to always locate sockets 30 centimeters from the floor. Switches and switches should be located at a height of 1.10 meters from the floor and 15 centimeters from the door frame. Crossovers are perfect for bedrooms because they allow light to be switched on from three different points.
What is the name of where the plug is connected?
A plug is made up of two elements: a plug and a socket (or outlet), which are connected to each other to establish a connection that allows the passage of electric current.
Which cable to use for outdoor electrical installation?
The cable for the outdoor electrical installation must be single-pole or multi-pole, made of copper and with a voltage of 0.6/1kV. In the case of subway installations they have to be inside cross-linked polyethylene pipes with polyvinyl chloride sheath.
How the wires run in a wall socket
The degree of electrification of a house refers to the electrical load that the electrical installation of the house must support. The REBT establishes two different degrees of electrification that will determine the minimum power that the installation will have to support to a tension of 230 volts, as well as the independent circuits with which the installation will have to count. These degrees of electrification are:
In this sense, the electrical installation of a dwelling with a basic electrification grade shall be capable of supporting a supply power of not less than 5,750 W at 230 V, regardless of the electrical power that the user of the dwelling may finally contract with the electricity supply company.
In any case, the maximum electrical power will correspond to the capacity of the installation, which will be defined by the value of the intensity designated for the installation’s automatic circuit breaker, as will be seen later on.
On the other hand, the linking installations are those that connect the general protection box with the user’s interior or receiving installations. Therefore, the general protection box is also a part of the link installation and constitutes the first element of the electrical installation of a house or a residential building, and therefore, it is usually located on the outside of the building on its exterior façade.
How high do the outlets go?
The recommended height of wall outlet boxes is approximately 12-18 inches (30-45 cm) from the top of the floor to the bottom of the outlet or receptacle box (or 16-22 inches to the top of the box).
How far apart should there be between outlets?
The distance between outlets would be a maximum of 3.60 meters, to ensure that there is always an outlet no more than 1.80 meters away.
Where to place a socket for a hood?
The socket where the hood is to be connected to the electricity should be placed above and behind the hood, so that it will be as inconspicuous as possible and without dangling wires.
Decorative outdoor electrical installation
These parameters define which materials should be used, what level of protection is required for each situation and what is the general routing of the installation, together with the location of each component. The main objective is to avoid the typical risks of these installations.
As a rule, the components of the installation have to be protected against dust and water with a minimum level set by the IP54 code. This corresponds to protection against dust particles and water jets.
Depending on the particularities of each garden, the average humidity and the intended use, the level of protection must be increased. Swimming pool areas, children’s areas or areas with high amounts of dust and humidity require a higher level of safety.
For terraces that are not covered or have pergolas, the protection requirements of the electrical installation are met with an IP4 or IP5 level. In the case of covered terraces, the protection level can be reduced to IP3 or IP2 if the ambient humidity levels are low.
What is the EU plug?
In general, the European plug is usually type C, while the English plug corresponds to type G and the American plug is type A. … Nowadays there are devices that serve both as a current and frequency transformer and a universal plug adapter.
What is the positive and negative in a plug?
If the multicolored wire is black and red, the black wire is the negative wire, while the red wire is positive. If both wires are black but one has a white stripe, the striped wire is negative, while the all-black wire is positive.
What color wire is used for the ground line in an electrical installation?
Green and yellow wire: ground wire. Blue wire: neutral wire. Until 1970 a red one was used. Brown wire: phase wire, although it can also be black or gray, depending on the color of the appliance that incorporates it.
How do the wires go in a three-prong plug?
The most important thing to take electricity out of the house, including an outdoor socket, is to plan well. Whether it is a patio, a terrace or a garden, the way to do it is simple. Whether through rigid pipes and surface mechanisms, or with concealed pipes, we tell you about it here!
Do you need to make minor electrical derivations in these spaces at home to put lamps, wall lights, outdoor sockets or switches? You can make a derivation from the inside of the house, starting from a junction box to the outside.
Make some grooves with plaster paste to embed the cables from the nearest junction box. These should always be run in corrugated pipe. Mark the appropriate height where to drill a hole and drill a hole to the outside. You will need a drill bit longer than the width of the wall to pass through.
Then run the cable between the junction box to the outside to insert the corresponding wires. Pull from the outside of the corrugated pipe until it is taut in place, preventing it from breaking when pulled. Finally, finish off the chase or chases, smooth them well with a trowel, let them dry, sand any imperfections and repaint that part of the wall or partition.